View UPD4713A_116777.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DATA SHEET
MOS INTEGRATED CIRCUIT
PD4713A
RS-232 LINE DRIVER/RECEIVER
The PD4713A is a high-voltage silicon gate CMOS line driver/reciever conforming to the EIA/TIA-232-E standard. It can operate with a single +5 V power source because it is provided with a DC-DC converter. In addition, this line driver/receiver has many ancillary functions, including output control, threshold select, and standby functions. Because the PD4713A is provided with three output driver circuits and three receiver circuits, it can constitute an RS-232 interface circuit with a single chip.
FEATURES
* Conforms to EIA/TIA-232-E (RS-232C) standard * +5 V single power source * Threshold select pin selecting two types of threshold voltages * Standby mode can be set by making standby pin high to reduce circuit current. * Three-state output configuration. Both driver and receiver outputs go into high-impedance state in standby mode.
ORDERING INFORMATION
Part Number Package 24-pin plastic DIP (300 mil) 24-pin plastic SOP (375 mil)
PD4713ACX PD4713AGT
Document No. S10318EJ3V1DS00 (3rd edition) Date Published April 1997 N Printed in Japan
(c)
1995
PD4713A
BLOCK DIAGRAM/PIN CONFIGURATION (Top View)
+10V + C3 C1 +5V Bypass capasitor +
1 2 3 4
VDD C1
+
DC - DC converter
C4
+
24
+ C4 + C2 -10V DCON Output control
GND 23 C4
-
VCC C1
-
22
VSS 21 300 300 20
Standby STBY 5 DIN1 TTL/CMOS INPUT DIN3 ROUT1 TTL/CMOS OUTPUT ROUT2 10 ROUT3 11 12 GND 8 9 DIN2 6 7
19 DOUT1 18 DOUT2 17 DOUT3 16 RIN1 RS-232 OUTPUT
300
5 k 5 k 5 k
RS-232 15 RIN2 14 RIN3 13 RCON Threshold control INPUT
* VDD and Vss are output pins of voltages internally boosted. Connecting a load directly to these pins is not recommended. ** The standby pin is internally pulled down. *** Use capacitors with a working voltage of 16 V or higher as C1 through C4. Insert a bypass Capasitor about 0.1 to 1 F between VCC pin to GND pin.
2
PD4713A
TRUTH TABLE Drivers
STBY H L L L DCON X L H H DIN X X L H DOUT Z L H L Remark Standby mode (DC-DC converter stops) Mark level output Space level output Mark level output
Receivers
STBY H L L RIN X L H ROUT Z H L Remark Stanby mode (DC-DC converter stops) Mark level input Space level input
Receiver input threshold voltage
RCON L H RIN1 A mode A mode RIN2 to RIN3 A mode B mode
H: high level, L: low level, Z: high impedance, X: H or L
3
PD4713A
ABSOLUTE MAXIMUM RATINGS (TA = 25 C)
Parameter Supply voltage Driver input voltage Receiver input voltage Driver output voltage Receiver output voltage Receiver input current Operating temperature range Storage temperature range Power dissipation Symbol VCC DIN RIN DOUT ROUT IIN TA Tstg PT Ratings -0.5 to +6.0 -0.5 to VCC +0.5 -30.0 to +30.0 -25.0 to +25.0 60.0 -40 to +85 -55 to +150 0.5
Note1
Unit V V V V V mA C C W
-0.5 to VCC + 0.5
Note 1. Pulse width: 1 ms, duty factor: 10 % MAX.
RECOMMENDED OPERATING RANGE
Parameter Supply voltage Receiver input voltage Operating temperature range External capacitance Symbol MIN. 4.5 -25 -20 4.7 TYP. 5.0 MAX. 5.5 +25 80 47 Unit V V C
VCC RIN
TA Note 2
F
Note 2.
The capacitance of an electrolytic capacitor decreases at a low temperature (0 C or lower). Determine the capacitance of the capacitor to be used taking this into consideration when the PD4713A is used at a low temperature. Keep the wiring length between the capacitor and IC as short as possible.
4
PD4713A
ELECTRICAL CHARACTERISTICS (OVERALL) (Unless otherwise specified, VCC = +5 V 10 %, TA = -20 C to +80 C, C1 to C4 = 22 F)
Parameter Circuit current ICC1 Circuit current ICC2 Standby circuit current ICC (Standby) Standby low-level input voltage Standby high-level input voltage Standby high-level input current Standby low-level input current Input capacitance CIN VIL (Standby) VIH (Standby) IIH (Standby) IIL (Standby) VCC = +5.5 V VI = 5.5 V VCC = +5.5 V VI = 0 V Driver input and receiver input VCC = +5 V, vs. GND, f = 1 MHz 10 pF -1 100 2.0 V Symbol Conditions VCC = +5 V, no load, RIN pin open (Standby pin open) VCC = +5 V, RL = 3 k (DOUT), DIN = GND, RIN and ROUT pins open (Standby pin open) VCC = +5 V, no load, RIN pin open (Standby pin high) Note 3 0.8 V 50 120 21.0 40.0 mA 5.0 18.0 mA MIN. TYP. MAX. Unit
A
A A
* TYP.: Typical (reference) value at TA = 25 C. Note 3. Because the standby pin is internally pulled down, if the standby pin is left open, operating mode is in effect.
ELECTRICAL CHARACTERISTICS (DRIVER) (Unless otherwise specified, VCC = +5 V 10 %, TA = -20 C to +80 C, C1 to C4 = 22 F)
Parameter Low-level input voltage High-level input voltage Low-level input current High-level input current Output voltage VDO Symbol VIL VIH IIL IIH VCC = +5.0 V, RL = , TA = 25 C VCC = +5.0 V, RL = 3 k VCC = +4.5 V, RL = 3 k Output short current Slew rate SR Propagation delay time
Note 4
Conditions
MIN.
TYP.
MAX. 0.8
Unit V V
2.0 0 0 9.7 5.5 5.0 15 1.5 1.5 9 4 0.8 40 30 30 -1.0 1.0
A A
V V V mA V/s V/s
ISC
VCC = +5.0 V, vs. GND CL = 10 pF, RL = 3 to 7 k CL = 2500 pF, RL = 3 to 7 k RL = 3.5 k, CL = 2500 pF VCC = VDD = VSS = 0 V
tPHL tPLH
s
10 50
Output resistance RO Standby output transition time Standby output transition time tDAZ tDZA
VOUT = 2 V Note 5 Note 5
300
500 4 25
s
ms
* TYP.: Typical (reference) value at TA = 25 C.
5
PD4713A
Note 4. Test point
If the output control pin is made low, the driver output goes low regardless of the driver input state.
6 ns 6 ns
5V Driver input 0V 90 % 1.5 V 10 % 10 % 90 % 1.5 V
tPHL VOH Driver output 90 % 3V -3 V
tPLH
3V -3 V
VOL
10 %
SR
SR
Note 5.
Test Point
5V
Standby input 0V
1.5 V
1.5 V
VOH Driver output VOL
+5 V High impedance -5 V +5 V -5 V
tDAZ
tDZA
Do not perform communication within the standby output transition time tDZA on power application or on releasing the standby mode.
6
PD4713A
ELECTRICAL CHARACTERISTICS (RECEIVER) (Unless otherwise specified, VCC = +5 V 10 %, TA = -20 C to +80 C, C1 to C4 = 22 F)
Parameter Low-level output voltage High-level output voltage Symbol VOL VOH VIL VIH
Note 7
Conditions IOUT = 4 mA IOUT = -4 mA RCON pin RCON pin RL = 1 k, CL = 150 pF
MIN.
TYP.
MAX. 0.4
Unit V V
VCC -0.8
Low-level input voltage High-level input voltage Propagation delay time
0.8 2.0 0.13 1 3 5 7 0.5 1.6 0.6 0.5 1.6 -0.4 2.6 2.2 1 1.2 2.2 -1.8 4.0 0.4 1 2.6 1.6 1.8 2.6 -3.0 5.4 1 10
V V
tPHL tPLH
s
mA k
Input current Input resistance Input pin release voltage Input threshold A mode (RCON pin low)
IIN RI VIO VIH VIL VH Input threshold A mode only VCC = +5 V VCC = +5 V VCC = +5 V (hysteresis width) VCC = +5 V VCC = +5 V VCC = +5 V (hysteresis width) Note 8 Note 8
V V V V V V V
s
ms
Input threshold B mode (RCON pin high)
Note 6
VIH VIL VH
Standby output transition time Standby output transiton time
tDAZ tDZA
* TYP.: Typical (reference) value at TA = 25 C. Note 6. Note 7. This data is applicable to receivers 2 and 3 only. Receiver 1 is fixed in A mode. Test Point
10 ns 10 ns
5V Receiver input -5 V 90 % VIL TYP. 10 % 10 %
90 % VIH TYP.
tPHL VOH Receiver output 1.5 V VOL 1.5 V tPLH
7
PD4713A
Note 8. Test Point
5V Standby input 0V 1.5 V 1.5 V
VOH Receiver output VOL
90 % High impedance 10 %
tDAZ
tDZA
The receiver output is undefined during the standby output transition time tDZA. Do not perform communication in the standby output transition time tDZA on power application or on releasing the standby mode.
8
PD4713A
TEST CIRCUIT
Driver output voltage/Output current ( + side)
+10V + C3 + C1 +5V
1 2 3 4 5 6
VDD C1
+
DC - DC converter
C4
+
24
+ C4 + C2 -10V +5V
GND 23 C4
-
VCC C1
-
22
VSS 21 300 300 20 19 18 17 16 5 k 15 5 k 14
STBY
7 300 8 9 10 11 12 GND
IDO
V VDO
5 k 13
Driver output voltage/Output current ( - side)
+10V + C3 + C1 +5V
1 2 3 4 5 6
VDD C1
+
DC - DC converter
C4
+
24
+ C4 + C2 -10V +5V
GND 23 C4
-
VCC C1
-
22
VSS 21 300 300 20 19 18 17 16 5 k 15 5 k 14
STBY
7 300 8 9 10 11 12 GND
IDO
V VDO
5 k 13
9
PD4713A
PACKAGE DRAWINGS
24PIN PLASTIC DIP (300 mil)
24 13
1
A I
12
K P L
J
H G
F D N
M
C B
M
R
NOTES
1) Each lead centerline is located within 0.25 mm (0.01 inch) of its true position (T.P.) at maximum material condition. 2) ltem "K" to center of leads when formed parallel.
ITEM MILLIMETERS A B C D F G H I J K L M N P R 33.02 MAX. 2.54 MAX. 2.54 (T.P.) 0.500.10 1.2 MIN. 3.50.3 0.51 MIN. 4.31 MAX. 5.08 MAX. 7.62 (T.P.) 6.4 0.25 +0.10 -0.05 0.25 1.0 MIN. 0~15
INCHES 1.300 MAX. 0.100 MAX. 0.100 (T.P.) 0.020 +0.004 -0.005 0.047 MIN. 0.1380.012 0.020 MIN. 0.170 MAX. 0.200 MAX. 0.300 (T.P.) 0.252 0.010 +0.004 -0.003 0.01 0.039 MIN. 0~15 P24C-100-300A-1
10
PD4713A
24 PIN PLASTIC SOP (375 mil)
24 13
detail of lead end
1 A
12 H
P
F
G
I
J
K
E
C D
NOTE
B M
M
L N
ITEM MILLIMETERS A B C D E F G H I J K L M N P 15.54 MAX. 0.78 MAX. 1.27 (T.P.) 0.40 +0.10 -0.05 0.10.1 2.9 MAX. 2.50 10.30.3 7.2 1.6 0.15 +0.10 -0.05 0.80.2 0.12 0.15 3 +7 -3
INCHES 0.612 MAX. 0.031 MAX. 0.050 (T.P.) 0.016 +0.004 -0.003 0.0040.004 0.115 MAX. 0.098 0.406 +0.012 -0.013 0.283 0.063 0.006 +0.004 -0.002 0.031 +0.009 -0.008 0.005 0.006 3 +7 -3 P24GM-50-375B-3
Each lead centerline is located within 0.12 mm (0.005 inch) of its true position (T.P.) at maximum material condition.
11
PD4713A
RECOMMENDED SOLDERING CONDITIONS
Soldering the PD4713A under the conditions listed in the table below is recommended. For soldering methods and conditions other than those recommended, consult NEC. Surface mount type For the details of the recommended soldering conditions of the surface mount type, refer to Information document "Semiconductor Device Mounting Technology Manual" (C10535EJ7V0IF00)
PD4713AGT
Soldering Method Infrared reflow Soldering Condition Package peak temperature: 235 C, Time: 30 seconds MAX. (210 C MIN.), Number of times: 2, Number of days: not limited* VPS Package peak temperature: 215 C, Time: 40 seconds MAX. (200 C MIN.), Number of times: 2, Number of days: not limited* Wave soldering Soldering bath temperature: 260 C MAX., Time: 10 seconds MAX., Number of times: 1, Number of days: not limited* Pin partial heating Pin temperature: 300 C MAX. (lead temperature), Time: 3 seconds MAX. (per lead pin), Number of days: not limited* WS60-00-1 VP15-00-2 Recommended Condition Symbol IR35-00-2
* The number of days the device can be stored at 25 C, 65 % RH MAX. after the dry pack has been opened. Caution Do not use two or more soldering methods in combination (except the pin partial heating method). Throught-hole type
PD4713ACX
Soldering Method Wave soldering Soldering Conditions Soldering bath temperature: 260 C MAX., Time: 10 seconds MAX.
REFERENCE DOCUMENTS
"NEC Semiconductor Device Reliability/Quality Control System" (IEI-1212) "Quality Grade on NEC Semiconductor Devices" (IEI-1209) "Semiconductor Device Mounting Technology Manual" (C10535EJ7V0IF00)
12
PD4713A
[MEMO]
13
PD4713A
[MEMO]
14
PD4713A
[MEMO]
15
PD4713A
[MEMO]
No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. Anti-radioactive design is not implemented in this product.
M4 96.5
14

▲Up To Search▲

Price & Availability of UPD4713A

	To Download UPD4713A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .